How to Clean Dyson V8 [Deep Cleaning]

***We may receive commissions on purchases made from our chosen links at no additional cost to you.

In this post, we are going to show you how to clean Dyson vacuum and how often you should clean it.

Table of Contents

How Often Should You Clean Your Vacuum

Each part of your vacuum may differ on how often you should clean it. So, we’ve made a little table for your guide.

Parts	Cleaning Schedule
Brushes and Bristles	After every use
Dust cup/Dust canister	After every few uses
Filters	Once a month
All Parts [Deep cleaning]	Once a year

And once in every decade, you may need to completely replace your vacuum. You can check the Dyson vacuums here.

How to Clean Dyson V8

Let’s start by cleaning your Dyson filter.

How to Clean Dyson V8 Filter

Dyson V8 has two filters:

Pre-motor filter. This sits in the middle of the cyclones.
Post-motor filter. You can see behind the motor.

In cleaning these filters, make sure to use only cold water. Do NOT any detergents.

Steps on How to Clean the Pre-Motor Filter

You can remove the pre-motor filter by pulling it out.
Remove any dust.
Then rinse it under running water.
Wring out excess water.
Dry it completely (at least 24 hours) before reattaching it to the vacuum.

This is optional, but if you want to clean the inner part of the filter, then you can use a blunt tool to remove the top part of the filter.

Gently push the clip. Once the cover is out it is easier to clean the inner part.

To prevent any downtime, you can also purchase an additional filter to use while waiting for it to dry completely.

Also check: 4 Causes Why Your Vacuum Cleaner Smells

Steps on How to Clean the Post-Motor or HEPA Filter

To remove the filter, twist it counterclockwise.
Remove excess dust.
Rinse your filter. Run the water over the filter’s outer surface until it runs clear. You can rub it gently with your hands to remove stubborn dirt.
Give your filter a firm shake. Fill up your filter with tap water. Using your hands, cover the ends and shake firmly to remove dirt.
Leave your filter to dry for at least 24 hours before you refit.

If you need an extra filter or want to replace your old filter you can check it below:

You can also check the video below on how to clean Dyson V8 filter.

Cleaning a Dyson V8 Brush Head

There are two types of cleaning heads for the Dyson V8, the fluffy attachment and the standard brush.

Dyson nozzles may have some features that can resist tangles, but it is still essential to check and clean the brush head. Any buildup of debris in the system will add friction and wear, which is not good for long-term performance.

How to Clean V8 Fluffy Tool

Remove the plastic clip. The roller bar is held in place by a plastic bolt underneath the fluffy attachment. You can use a coin to remove it.
Take out the roller attachment. You’ll see an arrow graphic on the right side of the tool. The soft roller can be removed by pushing this side down. A smaller roller component is also removed once this part has been removed.
Clean thoroughly. Now, it is easier to clean the nooks and crannies with all the components out. You can wash both the rollers, but avoid using detergents.
Refit the rollers. Make sure to completely dry the rollers before placing them back.

How to Clean V8 Cleaning Head

Remove the cap. The cap holding the brush in place can be removed using a coin.
Take out the brush. The cap will pop out as you twist it. You will need to remove the lid and brush, and then clean it. Use a scissor to cut the hair wrapping on the brush. Don’t forget to clean the wheels and the ball system. Also, check the axles for any debris accumulation. Then grab a microfiber and wipe down the components of the nozzle.
Refit the brush. Once you are done cleaning it, you can now reattach the brush. Still use a coin to twist and lock in place.

Clean a Dyson V8 Cyclone

We are now down to cleaning the cyclone, but before you do anything, bear in mind that this might void the warranty.

So, if you are Dyson is still under warranty, I would NOT recommend opening your cyclone.

And one more thing, do this only if you are confident that you are able to reassemble it. That means you are an electronic type of guy or that has already done some DIY.

Steps on How to Clean V8 Cyclone

Before you start dismantling the V8 cyclone, I recommend taking some photos on each step so you will have a guide once you reassemble it.

Remove the pre-motor filter.
Empty the dustbin. The red lever should be pulled to empty the contents, then pushed to release the dust container’s outer shell. If dirty, you can set it aside for now and clean it afterward.
Remove the cyclone assembly. Now that the dust bin outer shell is out, locate the red lever and push it. Then slide the whole assembly upwards. You will see four Torx screws, use a torque screwdriver to remove them. Once the screws are out, take out the component and place it in a ziplock bag or safe area.
Unfasten the screen filter. You can use a flat tool like a flat screwdriver and gently pull it upward as you rotate the filter. You will feel the clips loosen as you pull. And once you’ve loosened all the clips, pull out the mesh filter and wipe it with a clean microfiber towel. Or wash it with water but make you dry it completely.
Remove cyclones. As soon as you remove the mesh filter, you’ll be able to access the Torx screws holding the outer cyclone shell. Pull the cover after removing the four screws, and you will how dirty it is. Then remove the inner part, there is no screws holding it, so you just need to pull it out.
Disassemble the top cyclone assembly. The cyclones have four Torx screws inside and two outside. You may need a little help with a flashlight to find the inner screws. Once you’ve located and removed all the screws, dismantle it. Store all the screws in the ziplock bag so you won’t lose them.
Wash the cyclone component. Clean all the parts with running water. You can use an old toothbrush to remove stubborn dirt. Don’t scrub too hard as it may damage the component. After washing, let it dry completely before placing it back.

Reassemble Dyson V8 Cyclone

Attach the black gasket to the black component. The indentions are facing outward.
Reattach the cyclone cover.
Then join the red gasket.
Attach the inner cyclone. Check the five ports of the inner cyclone are in place.
Then install the outer cyclone and fasten the screws. There are six screws holding it, two are located on the outer part. And four screws you have to tighten in the cyclone.
Next is the inner cyclone cover. You just need to push it.
Attach the outer cyclone. Fasten the four screws on it.
The mesh filter should follow. Only clips are holding the mesh filter. Just push down until you hear the clips clamp on the frame. Make sure the mesh filter is securely fastened.
Then connect the red lever to the cyclone assembly. Fasten with the four screws.
Need to slide the cyclone assembly on the motor. Make sure you hear the clicking sound.
Lastly, reattach the clean dust bin.

In case you are having trouble following the instructions, below is the video to guide you on how to teardown and assemble it.

Conclusion

With this step-by-guide, you should be able to deep clean your Dyson V8 in no time. Clean the parts of your vacuum regularly to maintain its maximum efficiency.

Looking for more recommendations? Check out our related posts below!

Dyson Vacuum: Best Vacuum Cleaners [Complete List 2022]
9 Best Dyson Vacuum Alternatives Under $200
8 Best Cordless Vacuum for Pet Hair
12 Best Dyson Vacuum Alternatives